KISS-101IL

12" x 12" PCB In-Line

The KISS-101IL is the automated in-line version of the manual loaded KISS-101 machine, featuring the “Super fast” robotic motion to maximize production. The KISS-101IL performs the soldering of ‘through hole” components to PCBs in a “lights out” in-line process while maintaining the PCB stationary which prevents components from toppling over causing “unset” inter-metallic fillets. The KISS-101IL is an automated selective soldering machine using the proven ‘traveling mini–solder wave”.

Lead Solder Pot-Pump Assy
Heated N²
Programming Camera
KISS Board Warp Compensation System
Solder Level Check
Wave Height Verification
Solder Alloy Verification
Spray Fluxer
Witness Camera
Closed Loop Rotary Encoders
Fiducial Correction System
Included Solder Nozzles
Topside Preheater
Precision Drop-Jet Fluxer
Dropjet Verification System
Wave Nozzle Pump
Bullet Nozzle Set
KISS Pump Maintenance Kit
Dual Monitors
2ⁿᵈ Witness Camera
Lead-free Alloy Solder Pot & Pump
HMP Alloy Solder Pot & Pump
6 Channel Data Logger
SWAK-OS Offline Programming
Installation and Training*
Overall Dimensions: 54" x 40" x 45" (1371mm x 1016mm x 1143mm)
Weight of System: 650 Lbs.
Power: 120VAC/1PH/60Hz 15amps
Preheater Power: 208/220-240VAC/1PH/60Hz 15amps
Air Requirements: Min. 90 PSI • Max. 100 PSI
N² Requirements: 99.999% Pure @ Min. 60 PSI Max. 100 PSI
N² Consumption: 30-50 CFH
Max Work Area: 11" x 12" (279mm x 300mm)
PCB Thickness: Not Limited with proper support
Rail Width Adjust: Programmable

Complete Datasheet: View/Download

KISS-101IL

Additional Equipment

KISS Flux & Preheat Machines

The Selective Soldering process can be divided into three basic steps (fluxing, preheat, soldering). When all three steps are performed in one machine the total of the three steps determines the production rate, usually the fluxing and preheat time is approximately 50% of the production rate. By separating the flux and preheat operations from the downstream soldering machine the production rate can be doubled. The KFPHIL fluxer/preheater and the matching KISS in-line selective soldering machine provides this capability.

The KFPHIL in-line fluxer/preheat unit designed for our KISS-102IL, KISS-103IL and KISS-103ILDP models is an intelligent dual purpose system that significantly reduces process times by concurrently applying flux to the selected areas to be soldered then preheating the board in preparation for soldering. As the next board enters the KFPHIL, the previous board will be sent downstream to the KISS selective soldering machine.

The KPHIL is shown here working along side a KISS-103ILDP, adding pre-heat and fluxing before process, maximimizes efficiency and the bottom line.

N² Generators

ACE Production Technologies has partnered with Parker to produce the KNG Family of Nitrogen Generators to complement the KISS Selective Soldering systems. These generators are tailored to ACE’s specifications to provide adjustable purity and flow specific to your process. The generators work on the principle of compressed air passing through a series of molecular sieves. The nitrogen molecules are harvested while the O² and other gasses pass through. This process is completely automated requiring only compressed air.

The generators are turnkey requiring only 115VAC and compressed shop air. The controls are all solid state with a color touch screen interface. A digital oxygen meter (included) displays the PPM of oxygen so you can be assured of ab-solute purity.

The KNG generators are available in varying sizes to match the demands of single and multiple KISS machines. They provide continuous high quality nitrogen that is less expensive than cylinder service.

Load & Un-load Conveyors

Using conveyors to load and un-load PCB's dramatically speeds up processing.

View Complete Datasheet